Skip to main content

Measuring in the 3D property view in the web app

Learn how to measure lengths, heights, elevation changes, slopes, perimeters and surface areas in the 3D property view of the Duranta web app.

In the 3D property view, you can measure lengths, heights, elevation changes, slopes, perimeters and surface areas. Measurements follow the terrain, so sloped and raised areas are measured accurately.

Open Measure mode

  1. Open a property AI Map.

  2. Switch to the 3D property view.
    ​

  3. Click Measure in the bottom-right toolbar.
    ​

Click Measure again to turn measurement mode off.

Draw a measurement

  1. Click in the 3D view to place your first point, also called a node.

  2. Keep clicking to add more nodes.

  3. Each segment shows its length as you draw.

  4. Finish the measurement as either an open line or a closed shape.

Measure a line

Use an open line to measure distance.

Open lines are useful for:

  • Fence runs

  • Edging

  • Walkways

  • Paths

  • Sloped areas

  • Property features that do not need an enclosed area

Open lines are labeled Line 1, Line 2, and so on.
​

Measure an area

Use a closed shape to measure an enclosed area.

To close a shape, right-click. Then select the shape's label to see its card:

  • Surface area: the area of the ground or roof inside the shape, following its slope.

  • Surface perimeter: the length of the outline, following the terrain.

  • Volume: the space between the surface inside the shape and the ground under it, for example the size of a soil or mulch pile.

  • Slope: the angle and the grade of the surface inside the shape.

Closed shapes are labeled Polygon 1, Polygon 2, and so on.
​

Measure height and elevation

Duranta measures heights from 3D elevation data. To find how tall something is, such as a building, a wall or a fence, draw a line with two nodes: one on the ground and one on the top. Click the last node again to end the line, then select the line's label.

The card shows:

  • Total length: the length of the line.

  • Elevation A and Elevation B: the elevation at each end.

  • Elevation change: the height difference between the two ends. In the example below, the roof of the house is 16 ft above the front lawn.

  • Slope: the angle and the grade of the line.

Elevations and slope are shown for a line with two nodes. A line with more nodes shows its total length.

Edit a measurement

Saved measurements are editable in the 3D view.

Move a node

Click and drag any node to reposition it.

Raise or lower a node

In the 3D view, you can raise or lower nodes to better follow slopes, elevation changes, or raised surfaces.

This helps make measurements more accurate when the property is not flat.

Click a node and drag any of the arrows in its direction.
​

Add a node

Faint midpoint dots appear between existing nodes. Click one of these dots to add a new node.

Use this when you need to bend a line around a curve, obstacle, or property feature.
​

Undo and redo

Use undo and redo to step backward or forward through Measure changes.

  • Undo: ⌘Z on Mac or Ctrl+Z on Windows

  • Redo: ⌘⇧Z on Mac or Ctrl+Shift+Z on Windows

Measurements are shared with the 2D map

Measurements are shared between the 2D AI Map and the 3D property view.

A measurement you draw in 3D appears on the 2D map. A measurement drawn with the Ruler in 2D also appears in 3D.

Editing 3D measurements on the 2D map

If you edit a measurement on the 2D map that was originally created in 3D, Duranta may show this message:

Replace 3D measurement?
This area was measured in 3D. Editing the shape recalculates the area from the flat map and replaces the 3D value.

Choose Replace only if you want Duranta to recalculate the measurement using the flat 2D map. If you want to keep the original 3D measurement with elevation, cancel and edit it in the 3D property view instead.
​

Clear measurements

Click the trash button to delete all saved measurements from the property.

This removes every saved line and polygon, so use it only when you want to clear all measurements.
​

Where to use the Measure tool

  • Use the 3D Measure tool when elevation matters.

  • Use open lines for length.

  • Use closed shapes for area and perimeter.

  • Raise or lower nodes to better match slopes and terrain.

  • Measurements created in 3D are saved to the property and can also be viewed on the 2D AI Map.

Did this answer your question?